This guide explains all steps needed to get a pre-configured Alpitronic HYC 150 / 300 station connect to be.ENERGISED.
Instructions
-
Remove ChargePoint sticker and add be.ENERGISED QR-code sticker
-
Remove ChargePoint SIM card and add be.ENERGISED SIM-card
-
Install the charger, and configure the be.ENERGISED endpoint
Step-by-step guide
1. Remove ChargePoint sticker and add be.ENERGISED QR-code sticker
On the charging station there is a sticker that is not used anymore. This charger would only be used if the charger is connected to the ChargePoint CMS.
Remove this sticker, wipe off any residue with some isopropyl alcohol.
Now add the QR-Code stickers close to the connectors.
It is very important to put the stickers separately to differentiate between the available connectors. When used by the customer, only the scanned QR-code will initiate the charging process on this specific connector.
2. Remove ChargePoint SIM card and add be.ENERGISED SIM card
Remove the existing SIM card and insert the M2M SIM card for be.ENERGISED. (Alternatively, you can use any SIM card with public internet access or use the LAN port to connect via a public internet connection)
If the public Ethernet is used (either via SIM or Ethernet) you have to use the public endpoint (explained in step 3)
3. Install the charger, and configure the be.ENERGISED endpoint
Follow the installation guide provided for the hardware installation.
-
An ethernet cable is needed to connect your laptop to the Alpitronic station. The ethernet port on the Alpitrocnic station is located inside on the front door (display door) and is marked with XF2 - if XF2 is not available, you can use the ethernet port marked XF1 (depends on the hardware version)
-
When laptop and station are well wired via the ethernet cable you need to adjust your laptop network settings
-
Press the Windows + “R” simultaneously and Enter “ncpa.cpl” in the field then click OK :
-
Select the Ethernet Network for the Hypercharger , press the right button and open the properties:
-
Select "Internet Protocol Version 4 (TCP/IPv4)" with a mouse click and then click on
"Properties" :
-
Now select the "Use the following IP address" and enter the following values:
-
IP address: 192.168.1.101
-
Subnet mask: 255.255.255.0
-
Standard gateway: 192.168.1.1
-
-
Open a web browser, then enter the IP address : 192.168.1.100
-
When connecting to the web interface for the first time, you will be asked to enter a username
and password-
User Name : Contact Support to ask for the "OnRamp" Credentials for your charger
-
Password : Contact Support to ask for the "OnRamp" Credentials for your charger
-
-
Then you access to the main menu of the Hypercharger Web UI :
3.2 Go to OCPP and then select the tab “BOOT.INI FILE” and configure as follows
chargePointIdentity: leave configured ID or choose your own one
msgEngineType: json
WebSocketURL: ws://INSTANCE.private.ocpp-broker.com/ocpp/cp/socket/16
Replace “INSTANCE” with your corresponding part of the enpoint usually found in the browser-search-bar when logged in to be.ENERGISED.
Click “Save Configuration”.
3.3 Go back to the landing page and select “NETWORK” and go to the “SIM” tab.
Then go to “APN Configuration”
Leave the SIM Pin empty.
APN name: use the APN name found on the sticker of the provided SIM-card
APN user: use the APN user found on the sticker of the provided SIM-card
APN password: use the APN password found on the sticker of the provided SIM-card
Confirm with “Save Configuration” and restart the charging station by clicking on “RESET” and then “Soft Reset HYC”.
Once re-booted, the charger shows up in your system with the above configured chargePointIdentity.
Version: 2023-10-10 10:35:02 UTC